此智能交通信号系统利用环形线圈检测器来探测车道内车辆的通过，然后利
用 PLC 内置的计数器对车辆数量进行计数并计算出各方向车道的车辆滞留量。运用一
定的智能控制原则，控制系统就能依据车道内的滞留量情况自动地延长直行方向的绿灯
时长，从而提高十字路口的交通效率、缓解交通拥挤。
The intelligent traffic signal system uses the loop detector to detect the passing of vehicles in the lane, and then uses the loop detector to detect the passing of vehicles in the lane
The built-in counter of PLC is used to count the number of vehicles and calculate the vehicle detention in each direction. Use one
According to the given intelligent control principle, the control system can automatically extend the green light in the straight direction according to the detention amount in the lane
So as to improve the traffic efficiency and alleviate the traffic congestion. (2020-12-25, PLC, 3218KB, 下载1次)
西门子PLC高速计数器参考设置文件可使用
a ability abortion above absence absolutely abuse ... (2020-11-30, PLC, 8KB, 下载0次)
实现定时器和计数器的联合应用的实例，实现了一个抢答器的PLC控制程序
Program of Counter and Timer (2020-11-12, PLC, 1KB, 下载0次)
开发了以组态王为电梯模型软件环境、以PLC为实物控制器的六层电梯半实物仿真系统。首先构建了电梯模型，针对空间立体的电梯结构，采用平面分区域法建立电梯结构模型，将组态画面分为厅门轿厢及楼层显示区、外呼按钮区、轿厢内呼按钮区三大区；根据电梯结构和功能，定义了电梯模型与PLC的交互变量，并将变量与模型中元件进行动画连接，针对轿厢升降和门的开关运行动态，编写了脚本程序和事件命令语言程序。
A six storey elevator hardware in the loop simulation system with Kingview as elevator model software environment and PLC as physical controller is developed. Firstly, the elevator model is constructed. For the three-dimensional elevator structure, the plane partition method is used to establish the elevator structure model. The configuration screen is divided into three areas: hall door, car and floor display area, external call button area and car internal call button area. According to the elevator structure and function, the interactive variables between the elevator model and PLC are defined, and the variables are animated with the components in the model, According to the dynamic operation of the lift car and door, the script program and event command language program are written. (2020-10-08, PLC, 3718KB, 下载5次)
定时器TON1的使能端EN接在以其输出端TON1.Q为变量的常闭触点之后,实现定时器TON1的脉冲复位。当定时器TONI的输出端TON1.Q置位时,计数器CTUI的计数值CV1增1,实现分钟计时。当计数器CTUI的计数值CVI等于设定值60时,计数器CTUI的输出端CTU.Q置位,进而使计数器CTU1复位,从而实现小时定时。
The enabler EN of the timer TON1 is connected to the constant closed contact with the output TON1. Q as a variable to achieve the pulse reset of the timer TON1. When the output of the timer TONI is set to TON1.Q, the counter CTUI counting value CV1 is increased by 1 to achieve minute timing. When the counter (2019-03-22, PLC, 7KB, 下载0次)
倍福的编程文档,用于伺服控制的电机的单轴调试，以及各功能快的介绍
The Programming Document of Beifu (2019-03-05, PLC, 32531KB, 下载3次)
S7编程英文版用于西门子PLC可编程控制器 编程指令集安装使用以及接口调试
S7 Programming English Edition for Installation, Use and Interface Debugging of Siemens PLC Programmable Controller Programming Instruction Set (2019-01-31, PLC, 2170KB, 下载0次)
用于西门子PLC可编程控制器编程安装使用以及接口调试
Programming, Installation, Use and Interface Debugging of Siemens PLC Programmable Controller (2019-01-31, PLC, 2498KB, 下载0次)
通过松下PLC进行了伺服电机的位置控制和传感器数据的显示
Position control of servo motor and display of sensor data by Panasonic PLC (2018-12-03, PLC, 1940KB, 下载3次)
压滤机原控制发造，改为台达PLC控制，操作使用无线手持操作器操作，
The original control of filter press was changed to delta PLC control and operated by wireless hand-held manipulator (2018-06-28, PLC, 10KB, 下载0次)
西门子PLC的一些 相关资料，可以查看，还有一些变频器，HMI，S7-1200的一些手册相关文件
Some related information of SIEMENS PLC can be viewed, there are also some frequency converter, HMI, S7-1200's manual related documents. (2018-06-17, PLC, 12651KB, 下载7次)
传感器0.01用于检验产品好坏，当0.01为“ON”时，表示产品是好的，否则为坏的。速度检测器0.00测量流水线的速度，每得到个脉冲，代表产品向前移动一段距离d。速度检测器与传感器0.01的共同作用，可以决定那个产品好坏。若是坏的产品， 100.00为“OFF”，并控制推杆将坏的产品推到滑道上去，同时传感器0.02会检测到这个坏的产品已经到了滑道上，并使推杆退回。
plc item product testing (2018-04-01, PLC, 3KB, 下载1次)