[嵌入式/单片机/硬件编程] Http_demo_SUB-1GHZ
web网页嵌入到嵌入式系统中，但平常写的web都比较大，我这里提供一个比较轻型的web网页，可以轻松嵌入到各种嵌入式系统中，很小，很全，和稳定。里边我删除了公司logo，如果需要显示logo的，加个logo.png文件进去即可，但加入的logo定要小，反显透明即可
Web pages are embedded into embedded systems, but usually the web pages written are relatively large. Here I provide a relatively light web page, which can be easily embedded into various embedded systems, small, complete, and stable. I deleted the company logo inside, if you need to display the logo, add one logo.png The file can be entered, but the logo must be small and transparent (2020-09-30, C/C++, 251KB, 下载3次)
[嵌入式/单片机/硬件编程] 温湿报警
实时显示周围环境温湿度，与所设温湿度区间不符立即蜂鸣报警， 具有报警消音功能，s1循环设置，s2加，s3减，s4报警消音
Display the temperature and humidity of the surrounding environment in real time. If it is inconsistent with the set temperature and humidity range, it will give an alarm immediately,With alarm silencing function,S1 cycle setting, S2 plus, S3 decreasing, S4 alarm silencing (2020-09-23, C/C++, 3KB, 下载1次)
[嵌入式/单片机/硬件编程] NJ_test19052309.part07
车载测算终端，使用STM32F103主控芯片，加上移远GPS+4G模块，上传行驶轨迹，后台计算面积。典型的物联网车载终端产品，方便移植到其他物联网产品上。
Using STM32F103 main control chip, plus the GPS + 4G module, upload the driving track, and calculate the area in the background. The typical Internet of things vehicle terminal products are easy to transplant to other Internet of things products. (2019-12-24, C/C++, 1576KB, 下载18次)
[嵌入式/单片机/硬件编程] ADC加平均滤波（判断字符串）
这是不经任何处理直接到单片机引脚上的采样，主要利用算法，如果外加硬件电路做下处理，可做到采样不跳动。
This is the sampling directly to the pin of the single chip without any processing, mainly using the algorithm, if the hardware circuit is added to do the next processing, the sampling can be done without jumping. (2019-06-25, C/C++, 354KB, 下载3次)
[嵌入式/单片机/硬件编程] RTC-timer
基于stm32f103的RTC实时时钟，功能有：采用oled液晶屏显示时间和日期，可通过按键或者红外遥控来控制修改时间，加温度显示等。
RTC real-time clock based on STM32F103 has the following functions: using OLED LCD screen to display time and date, controlling modification time by keys or infrared remote control, adding temperature display, etc. (2019-05-16, C/C++, 474KB, 下载7次)
[嵌入式/单片机/硬件编程] TM1637驱动力位共阳数码管51程序加仿真
TM1637的51单片机测试程序，仿真成功，有仿真结果，可以方便灵活使用。
TM1637 51 single chip computer test program, simulation success, simulation results, can be convenient and flexible to use. (2019-01-28, C/C++, 60KB, 下载20次)
[嵌入式/单片机/硬件编程] 数字DL100、DH101模数转换
DH100/DH101数字模数传感器开发包，适用于链接模拟量传感器，具有24位AD转换功能，和连接电路 ，附有惠更斯电桥电路，适用于称重传感器等的嵌入式系统设计。
DH100/DH101 digital analog and digital sensor development kit is suitable for linking analog sensor. It has 24-bit AD conversion function and connection circuit. It also has Huygens bridge circuit. It is suitable for embedded system design of weighing sensor and so on. (2019-01-21, C/C++, 5135KB, 下载0次)
[嵌入式/单片机/硬件编程] NBLOT
NBLOT网络，采用BC95芯片，实现数据的上传与下发；附加文档，如何与电信平台连接，如何取数据
NBLOT network, using BC95 chip, data upload and download; additional documents, how to connect with the telecommunications platform, how to get data (2018-10-29, C/C++, 16773KB, 下载22次)
[嵌入式/单片机/硬件编程] KeyScan
只需一条线，理论上可接16个按键，但实际不行，按键上要加一个104的电容，保证稳定。参考电压和案件判断参考值在中断中修改，若觉得麻烦，可以通过宏定义实现。有些函数没作用可以注释掉。
Only one line, in theory can be connected with 16 keys, but not in practice, the key to add a 104 capacitance, to ensure stability. The reference voltage and the reference value of the case judgment are modified in the interruption. If it is in trouble, it can be implemented by a macro definition. Some functions can be annotated if they do not work. (2018-01-23, C/C++, 1KB, 下载1次)
[嵌入式/单片机/硬件编程] 1-GSM主程序加烟雾
建立了一个基于GSM网络及短信息平台上的家庭安防系统，设计中采用了STC89C52单片机系统、无线GSM短信模块及传感器技术。
The system in this paper has some advantages, such as simple hardware structure and high cost-performance and so on. The Modularized program is convenient to expansion of the system. The test results indicated that the family security system based on short message platform realizes long distance alarm and control function, and achieves the goal of long distance monitoring and controlling towards family. It has good application prospects. (2017-12-31, C/C++, 31KB, 下载1次)
[嵌入式/单片机/硬件编程] AD转换
模数转换包括采样、保持、量化和编码四个过程。是将连续的模拟量（如象元的灰阶、电压、电流等）通过取样转换成离散的数字量
Analog to digital conversion involves sampling, holding, quantizing, and encoding four processes. Is the continuous analog (gray scale, such as voltage and current element etc.) is converted into digital quantity by discrete sampling (2017-08-04, C/C++, 2564KB, 下载4次)
[嵌入式/单片机/硬件编程] 遥控器源代码 V1.0
无人机的遥控代码
传感器运用的是 MPU-6050是6轴运动处理传感器。它集成了3 轴MEMS 陀螺仪，3 轴MEMS加速度计，以及一个可扩展的数字运动处理器DMP（Digital Motion Processor），可用I2C接口连接一个第三方的数字传感器，比如磁力计。MPU-60X0 也可以通过其I2C 接口连接非惯性的数字传感器，比如压力传感器。
UAV remote control code (2017-08-01, C/C++, 10965KB, 下载8次)
[嵌入式/单片机/硬件编程] 单片机定时器实现秒计时和显示
1 基础部分：
（1） 用51的p1口作为数据输出口，p2口为共阴数码管位选信号，利用定时器0实现秒计时和显示。
（2） 上电复位后，显示00。
（3） 按键按下S2键后开始计数。采用加法计数形式。计到60停止。蜂鸣器鸣响。
（4） 鸣响2秒后停止，恢复显示00。
（5） 当再次按下S2键后重复1-4过程。
2 提高部分：
利用S2，S4，S6完成进入设置；进行数字十位和个位设置；存储，启动等动作；
工作过程如下：
（1）第一次按下S6，进入十位数设置；此时，每按下S4一次，十位数码管显示加1，从0至9滚动显示；
（2）第二次按下S6，十位显示固定在当前值；进入个位数设置；此时，每按下S4一次，个位数码管显示加1，从0至9滚动显示；
（3）第三次按下S6，十位和个位显示数值固定；
（4）设置完成后按下S2，数码管显示00；系统从0计时，当计到设置值时，蜂鸣器响一秒钟；
（5）蜂鸣器停止后，系统显示设置值，再次按下S2可以重新开始计时；或不按下S2，按下S6则重复（1）至（4）过程。
（注：本试验可以采用两种方法来做：1软件计数法，2定时中断法）
1 Basic part:
(1) use the 51 P1 port as the data output port, and the P2 port is the co Yin digital tube bit selection signal, and the timer 0 is used to realize the timing and display of seconds.
(2) after power on reset, display 00.
(3) press the S2 button and start counting. Use addition counting form. It stops at 60. Buzzer ringing.
(4) stop after 2 seconds, and resume 00.
(5) repeat the 1-4 procedure when the S2 key is pressed again. (2017-06-03, C/C++, 257KB, 下载4次)
[嵌入式/单片机/硬件编程] three-ways-to-find-the-gross-error
/*
name:用三种方法寻找粗大误差
Copyright:
Author: Mr.Lai
IDE:Dev-C++ 4.9.9.2
Date: 28/03/13 13:51
Description:莱以特准则、格罗布斯准则 和狄克松准则寻找粗大误差
*/
/* Name: three ways to find the gross error Copyright: Author: Mr.Lai IDE: Dev-C++ 4.9.9.2 Date: 28/03/13 13:51 Description: Knight to special standards, guidelines and Dick Globus loose criteria to find the gross error* / (2014-03-31, C/C++, 28KB, 下载13次)
[嵌入式/单片机/硬件编程] motor_angle
步进电机的控制程序，有四个键来控制：调零键，加角度键，减角度键，运行键。通加减角度达到需要的角度，按运行即可转到需要的角度。单片机是stc89c52
Stepper motor control program, there are four keys to control: zero key, plus the angle button, reducing the angle button, run key. Achieve the required angle through the angle of plus or minus, according to the angle of operation needs to go. SCM is stc89c52 (2011-03-05, C/C++, 53KB, 下载84次)
[嵌入式/单片机/硬件编程] STC1TRunOCM12864
应用STC12C5A60S2，在12M晶振的情况下运行的OCM12864液晶，调试通过。这个时序在低于是12M的1T单片机上可能性运行，如果晶振频率在往上加的话，将时序中的延时加长即可。
Application STC12C5A60S2, 12M crystal in the case of running OCM12864 LCD, debugging through. The timing is less than 12M in the possibility of running 1T microcontroller, the crystal frequency if added up, it will lengthen the timing of the delay can be. (2010-12-13, C/C++, 27KB, 下载6次)
[嵌入式/单片机/硬件编程] PROTEUS
基于PROTEUS的游戏的3个游戏，俄罗斯方块程序，于16×16点阵的贪吃蛇仿真，基于PROTEUS的推箱子游戏
PROTEUS-based game three games, Tetris program, on the Snake 16 × 16 lattice simulation, based on the Sokoban game PROTEUS (2010-04-06, C/C++, 2646KB, 下载119次)
[嵌入式/单片机/硬件编程] kaijicishujiyi
每次开机都将次数加1 并存储到EEPROM。这样就能直观的看到机器的使用次数。用P1口 LED做为显示，次数大于256是将溢出，按复位模拟开机 或者直接通过开关开机。
Each boot will add a number of times and stored in EEPROM. This will be able to see the intuitive usage of the machine. As with the P1 port LED display, frequency is greater than 256 is the overflow, according to reset the boot, or directly through the analog switch boot. (2009-12-14, C/C++, 15KB, 下载15次)
[嵌入式/单片机/硬件编程] Sysinternals
这里面包含了很多的工具, 其中有DbgView这个非常方便的工具, 如进行VC编时, 在程序中加一句OutputDebugString("debug info"), 就可输出信息到DbgView这个工具中查看,非常方便.
There contains a lot of tools, one of DbgView there is this very convenient instrument, such as for VC allocation, the process at an add OutputDebugString ( " debug info" ), you can output this information to the instrument DbgView view, very convenient. (2009-03-13, C/C++, 8184KB, 下载37次)