能够实现labview和tcp的互链，并且上传数据
It can realize the mutual link between LabVIEW and TCP, and upload data (2021-03-11, C/C++, 816KB, 下载0次)
实现基于多线程的异步定时器,右纯代码创建
Implement asynchronous timer based on multithreading, create right pure code (2020-07-20, C/C++, 587KB, 下载0次)
LabVIEW入门与实战开发100例： Trigger Counter，触发计数器使用方法
LabVIEW introduction and practical development 100 cases: trigger counter, trigger counter usage (2020-05-19, C/C++, 123KB, 下载0次)
将任意输入的摄氏温度转换成华氏温度，并分别显示在温度计中。可以任意设置输入上限下限，并设置警灯和蜂鸣器来提示是否超过所设置的范围，并伴有字符串的温度状态显示（超过范围/未超过范围）。警灯和整个程序分别由警灯开关和总开关控制。
Convert any input Celsius temperature to Fahrenheit temperature and display them in the thermometer respectively. The upper and lower limit of input can be set arbitrarily, and the alarm light and buzzer can be set to prompt whether the set range is exceeded, with the temperature status display of string (over range / not over range). The alarm light and the whole program are controlled by the alarm light switch and the main switch respectively. (2020-03-13, C/C++, 10KB, 下载0次)
定时器定时通过UDP发送时间戳，可设置起始结束时间
Timer sends timestamp through UDP (2019-07-05, C/C++, 787KB, 下载0次)
数据采集模块 主要完成数据采集的控制，包括触发控制、通道选择控制、时基控制等。其中： 1）触发控制包括触发模式、触发斜坡、触发电平控制； 2）通道选择主要控制单通道或双通道测量； 3）时基控制主要控制采集卡扫描率、每一通道扫描次数(取样数)。
Data acquisition module mainly completes data acquisition control, including trigger control, channel selection control, time-based control and so on. Among them: 1) trigger control includes trigger mode, trigger ramp and trigger level control; 2) channel selection mainly controls single channel or double channel measurement; 3) time-based control mainly controls the scanning rate of acquisition card and the number of scanning times per channel (sampling number).
Data acquisition module mainly completes data acquisition control, including trigger control, channel selection control, time-based control and so on. Among them: 1) trigger control includes trigger mode, trigger ramp and trigger level control; 2) channel selection mainly controls single channel or double channel measurement; 3) time-based control mainly controls the scanning rate of acquisition card and the number of scanning times per channel (sampling number). (2019-07-02, C/C++, 918KB, 下载5次)
电机控制器的串口通信界面,基于labview visa,德马克电机
Serial communication interface of motor controller based on LabVIEW visa, demarcation motor (2019-07-02, C/C++, 773KB, 下载3次)
编写VI程序完成，已知三角形三个边长A、B、C，计算三角形的面积S。
此程序目的是熟悉前面板、框图程序和图标/连接器的使用方法
The VI program is written. The three sides of the triangle are known as A, B and C, and the area of the triangle is S.
The purpose of this procedure is to familiarise yourself with the use of front panel, block diagram program and icon / connector. (2018-11-21, C/C++, 9KB, 下载0次)
1、使用for循环写出n！的程序。（利用移位寄存器或是反馈节点实现）。
知识点：for循环的参数设置，循环总数以及循环计数参数的使用，注意总数的设置和移位寄存器的初始化。
2、创建VI，在前面板上放置3个LED。程序运行时，第一个LED打开并保持打开状态。1秒以后，第二个LED打开并保持打开状态；再过2秒，第三个LED打开并保持打开状态。所有LED都保持打开状态3秒，然后程序结束。
知识点：使用3帧单层顺序结构，每帧包含延时函数。
2, create VI, and place 3 LED on the front panel. When the program is running, the first LED is turned on and kept open. After one second, the second LED is turned on (2018-06-08, C/C++, 16KB, 下载1次)
ADuCM360NoiseAnalysis是ADI公司的带有16位AD的M3系列处理器，这是测试其AD性能的底层固件及Labview的源代码
ADuCM360NoiseAnalysis is ADI' s 16-bit AD with a series of M3 processor, which is a test of the underlying performance of its AD and Labview firmware source code (2016-11-14, C/C++, 111KB, 下载2次)